Walkthrough model workflow reuse - Revision history

Daniel Castaño at 09:29, 4 March 2025

2025-03-04T09:29:53Z

2025-03-04T09:28:56Z

2024-12-03T10:59:49Z

2024-12-02T12:52:02Z

2016-08-17T04:54:18Z

2016-08-17T04:49:22Z

2016-08-17T04:36:29Z

2016-08-17T04:36:06Z

2016-08-17T04:35:35Z

2016-08-17T04:25:04Z

@@ Line 42: / Line 42: @@
 [[File:modelReuseFilament2.png|thumb|center|300px|Next filament is chosen]]
-and then define a new filament model, and '''click''' on some points on it, as done on the previous filament. But in this case, afterwards we save  the model without further edition: we don't produce crop points directly.
+and then define a new filament model, and '''click''' on some points on it, as done on the previous filament. But in this case, afterwards we save  the model without further edition: we don't try produce crop points directly with the Worfklow Model Editor GUI.
 {|style="margin: 0 auto;"

@@ Line 42: / Line 42: @@
 [[File:modelReuseFilament2.png|thumb|center|300px|Next filament is chosen]]
-and then define a new filament model, and click on their points. But in this case, afterwards we save  the model without further edition
+and then define a new filament model, and '''click''' on some points on it, as done on the previous filament. But in this case, afterwards we save  the model without further edition: we don't produce crop points directly.
 {|style="margin: 0 auto;"

← Older revision		Revision as of 12:52, 2 December 2024
Line 1:		Line 1:
		+	[[Category:Walkthroughs]]
		+
	This walkthrough shows how to reuse the geometric computations performed on a single model onto a larger set of models.		This walkthrough shows how to reuse the geometric computations performed on a single model onto a larger set of models.

@@ Line 55: / Line 55: @@
 Now, the catalogue should see three models inside this tomogram entry.
-[[File:modelReuseCatalogue.png|thumb|center|300px|XXX]]
+[[File:modelReuseCatalogue.png|thumb|center|300px|]]
 If we open the tomogram with the volume list manager, we will get a list of those models. We should see that the first we created does contain some crop points, but the other two don't.
 {|style="margin: 0 auto;"
 | [[File:modelReuseVolumeListOpen.png|thumb|upright|400px|  ]]
-| [[File:modelReuseVolumeListFirstStatus.png|thumb|upright|400px|three filament models ]]
+| [[File:modelReuseVolumeListFirstStatus.png|thumb|upright|400px|  ]]
 |}

@@ Line 52: / Line 52: @@
 | [[File:modelReuseFilament3.png|thumb|upright|400px|  ]]
 | [[File:modelReuseFilament3Points.png|thumb|upright|400px|three filament models ]]
 |}

← Older revision	Revision as of 10:59, 3 December 2024
(No difference)

@@ Line 44: / Line 44: @@
 {|style="margin: 0 auto;"
 | [[File:modelReuseFilament2Points.png|thumb|upright|400px|  ]]
-| [[File:modelReuseFilament2Save.png|thumb|upright|300px|  ]]
+| [[File:modelReuseFilament2Save.png|thumb|upright|400px|  ]]
 |}
@@ Line 51: / Line 51: @@
 {|style="margin: 0 auto;"
 | [[File:modelReuseFilament3.png|thumb|upright|400px|  ]]
-| [[File:modelReuseFilament3Points.png|thumb|upright|300px|three filament models ]]
+| [[File:modelReuseFilament3Points.png|thumb|upright|400px|three filament models ]]
 |}

← Older revision		Revision as of 04:35, 17 August 2016
Line 33:		Line 33:
	Now can save the workflow itself, probably providing first a different name than the default.		Now can save the workflow itself, probably providing first a different name than the default.

−	[[File:ReuseWorkflowChangeName.png\|thumb\|center\|300px\|Provide a name for the workflow. It will be saved later into the catalogue]]	+	[[File:ReuseWorkflowChangeName.png\|thumb\|center\|300px\|Provide a name for the workflow. It will be saved later into the catalogue]].
		+
		+
		+	Once the workflow defined on the first model is defined we can move to a different filament and pick its extremal points with controls [1] and [2]:
		+
		+	[[File:modelReuseFilament2.png\|thumb\|center\|300px\|Next filament is chosen]]
		+
		+	and then define a new filament model, and click on their points. But in this case, afterwards we save the model without further edition
		+
		+	{\|style="margin: 0 auto;"
		+	\| [[File:modelReuseFilament2Points.png\|thumb\|upright\|400px\| ]]
		+	\| [[File:modelReuseFilament2Save.png\|thumb\|upright\|300px\| ]]
		+	\|}
		+
		+	and move to the generation of a further filament model
		+
		+	{\|style="margin: 0 auto;"
		+	\| [[File:modelReuseFilament3.png\|thumb\|upright\|400px\| ]]
		+	\| [[File:modelReuseFilament3points.png\|thumb\|upright\|300px\|three filament models ]]
		+	\|}

← Older revision		Revision as of 04:25, 17 August 2016
Line 30:		Line 30:

	[[File:ReuseWorkflowSaveModel.png\|thumb\|center\|300px\|Saving the ''model'']]		[[File:ReuseWorkflowSaveModel.png\|thumb\|center\|300px\|Saving the ''model'']]
		+
		+	Now can save the workflow itself, probably providing first a different name than the default.
		+
		+	[[File:ReuseWorkflowChangeName.png\|thumb\|center\|300px\|Provide a name for the workflow. It will be saved later into the catalogue]]